Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Pembroke Pines?
Gate access control in Pembroke Pines typically runs $350 to $1,200 for a keypad, card reader, or intercom entry system, while a full multi-unit setup with a vehicle loop, remote transmitters, and a control board can reach $2,400 or more. Most single-family homeowners we quote land between $450 and $850 for a working keypad-and-opener combination. The written estimate sets the final price, and estimates are free.
Key Takeaways
- Simple keypad entry: $350 – $600 installed.
- Card reader or proximity system: $500 – $1,200.
- Vehicle loop detector added to a gate: $450 – $900.
- Control board replacement on an existing system: $300 – $750.
- Intercom or telephone entry (DoorKing-style): $700 – $2,200.
- Commercial multi-tenant setup: $1,500 – $4,000+ depending on reader count and wiring runs.
Gate Access Control Cost Breakdown (2026)
Access control is a broad term. It covers everything from a single keypad on a residential swing gate to a networked card system at an HOA or a small commercial property. The ranges below reflect what these jobs typically cost in the Pembroke Pines market in 2026, based on the equipment and labor involved. Your exact figure depends on the gate, the wiring already in place, and the level of entry you want.
| Line Item | Typical Cost Range | What It Covers |
|---|---|---|
| Residential keypad entry | $350 – $600 | Weather-rated keypad, wiring to the control board, programming |
| Card reader or proximity reader | $500 – $1,200 | Reader unit, credentials, wiring, integration with existing opener |
| Vehicle loop detector | $450 – $900 | Loop saw-cut, loop wire, detector board, re-seal, wiring |
| Intercom or telephone entry | $700 – $2,200 | Entry station, call button, phone or app connectivity |
| Control board replacement | $300 – $750 | New board, reprogramming, safety check |
| Remote transmitter programming | $75 – $200 | Replacement or additional remotes, pairing to existing receiver |
| Safety photo-eye or edge sensor | $150 – $450 | Sensor pair, mounting, alignment, test |
| Full commercial multi-tenant system | $1,500 – $4,000+ | Multiple readers, network controller, software setup, cabling runs |
What pushes a quote toward the top of a range? Long wiring runs across a driveway or from a clubhouse to a gate. A control board that needs to be replaced at the same time as the reader. Adding a vehicle loop under existing concrete, which means cutting and re-sealing. Commercial systems with multiple readers and tenants usually sit at the top of the range because every reader adds hardware and every tenant adds programming. On the lower end, a straightforward keypad swap on a gate that already has good wiring is one of the simpler jobs we see in Pembroke Pines.
We work on gates, only gates. That matters on a job like this because access control is where gate hardware, low-voltage wiring, and the opener’s own control logic all meet. A generalist contractor who also installs fencing or does electrical work may know part of the picture. A gate technician who has opened the same control board on a LiftMaster, FAAC, or DoorKing unit dozens of times already knows what he’s looking at before the cover comes off.
What Affects Gate Access Control Pricing in Pembroke Pines
Several things move the number up or down. Here are the ones we see most often in this city.
- Gate type and weight. A light residential swing gate can take a standard opener and off-the-shelf keypad. A heavy slide gate or an ornamental steel gate may need commercial-grade hardware, deeper footings, and a more capable control board. Heavier gates cost more to control.
- Existing wiring and power. If a gate already has a working operator, low-voltage wire run to a keypad location, and a 120V feed at the post, the install is faster and cheaper. If power needs to be brought to the gate or the low-voltage run is missing, that’s added labor and materials.
- Brand of opener. We service nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Whether your property runs a LiftMaster or a FAAC, we already know the system. Accessory compatibility varies by brand, and some platforms accept a wide range of third-party readers while others are more locked down. The brand in place shapes which parts fit and how long the job takes.
- Reader count and tenants. A single-family home with one keypad is a straightforward number. An HOA gatehouse with three readers, a directory, and forty tenant credentials is a much larger job in both hardware and setup time.
- Wiring distance. Pembroke Pines lots can run deep from the street to the gate. A long driveway means a longer wire run, more conduit, and more labor. Distance adds cost even when the hardware is identical.
- Whether the panel is inside or outside. An exterior post-mounted keypad or reader must be weather-rated and mounted to survive summer thunderstorms and afternoon downpours. That’s different hardware than an interior control panel, and it’s priced accordingly.
How to Save on Gate Access Control
Access control isn’t a place to cut corners on safety, but there are real ways to keep the bill down.
- Fix what you have before adding new. If your gate already has a control board and a working opener, a failed keypad or a dead reader is often a smaller repair than a full upgrade. We diagnose the existing hardware first. From a broken hinge to a failed control board, one call covers it.
- Group the work. If you already know the opener needs attention, schedule the access control upgrade alongside it. One visit covers both, and that saves on labor.
- Match the hardware to the gate. A residential swing gate doesn’t need a commercial reader designed for a fifty-tenant HOA. Tell us how many people and vehicles actually use the gate, and we’ll quote the right level of system.
- Ask about compatibility. Some existing openers accept a broad range of readers and keypads. Others don’t. Knowing which before you buy parts saves money.
- Get the estimate in writing. Our estimates are free, and the written estimate sets the final price. Call (877) 748-7198 and we’ll walk the gate and quote it.
One more thing worth saying: access control is where a gate gets dangerous, too. The operator’s wiring carries line voltage, and a gate with a failed safety sensor or a mis-wired control board can injure someone. We don’t encourage homeowners to open control panels or chase low-voltage wiring themselves. That’s exactly the kind of work a trained gate technician should handle. The operator’s power and the heavy panels are the two parts of a gate system that hurt people, and access control touches both.
Can I Get Gate Access Control Installed on a Manual Gate?
Yes. A manual gate can be automated and given access control in one job, and that’s a common request. The work splits into two parts: adding an operator to motorize the gate, and then adding the keypad, reader, or remote receiver that controls it. We handle both under one service, which means you don’t source one contractor for the opener and another for the entry hardware. If your gate is currently manual and you want vehicle access without leaving the car, we quote the opener and the access control together so the wiring is planned once.
Do I Need a Permit for Gate Access Control in Pembroke Pines?
Often, yes. Most cities require a permit when you add or replace an electric gate operator or run new electrical work to a gate, and that includes the low-voltage and line-voltage wiring that access control depends on. The rules vary by property and by the scope of the work, so the right move is to ask the city’s building department before the job starts. We’ll tell you what we’ve seen on similar Pembroke Pines jobs, and we’ll work with whatever the city requires. Our technicians have up to 9 years of experience with gate operators and control wiring, and they’ll flag a permitting question before they start rather than after.
Can You Repair an Existing Access Control System Instead of Replacing It?
Usually, yes, and it’s often the cheaper path. A dead keypad, a reader that stopped reading cards, a control board with a failed relay, or a safety sensor that won’t align are all repairable on most systems. We diagnose the existing hardware first. If the opener and the gate are otherwise sound, replacing one component is far less expensive than a full system swap. For older systems where parts are no longer available, we’ll tell you that plainly and quote the replacement. Electric gate acting up? That’s exactly what we’re built for. Our Pembroke Pines page covers the full range of gate services in this city.
FAQs – Gate Access Control Cost
How much does gate access control cost in Pembroke Pines?
Gate access control in Pembroke Pines typically costs $350 to $1,200 for a keypad, card reader, or intercom, and $1,500 to $4,000+ for a full commercial multi-tenant system. Most single-family homeowners land between $450 and $850. The written estimate sets the final price. Call (877) 748-7198 for an exact quote – estimates are free.
Is it cheaper to repair or replace an access control system?
Repair is usually cheaper when the opener and gate are sound and only one component has failed. A control board replacement runs $300 to $750, while a full swap with new readers often runs $1,200 or more. We diagnose first, then quote the cheaper path when it’s the right one. Call (877) 748-7198 for a free estimate.
How much does a keypad entry system cost in Pembroke Pines?
A residential keypad entry system in Pembroke Pines typically costs $350 to $600 installed, including wiring and programming. If power or low-voltage wire needs to be run to the gate, the figure climbs. Call (877) 748-7198 and we’ll quote your gate.
How long does gate access control installation take?
A single keypad or reader on an existing opener usually takes a few hours. A commercial system with multiple readers and tenant setup takes longer, often a full day or more depending on wiring runs and the number of credentials. We answer 24/7. Fast dispatch from 7am to 7pm. Call (877) 748-7198 to schedule.
Can you come today?
Same-day service is often possible when you call early. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (877) 748-7198 and we’ll find the soonest slot for your gate.
Do you work on commercial gate access control?
Yes. We service both residential and commercial gate systems, including FAAC, BFT, and DoorKing, which are common on managed properties and HOAs. Commercial systems with multiple readers and door directory integration are within what we do. Call (877) 748-7198 for a quote.
Which brands do you work on?
We service nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Whether your property runs a residential Ghost Controls opener or a commercial DoorKing entry system, we already know the platform. Call (877) 748-7198 with your brand and model number.
Your gate is your property’s first line of security. We treat the repair accordingly. If you’re in Pembroke Pines and your access control isn’t working the way it should, the fastest way to a real number is a call. Contact Tidewater Gate Repair today for a free estimate at (877) 748-7198. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 9 years of experience on gate systems across South Florida, and from a broken hinge to a failed control board, one call covers it.
Written by the team at Tidewater Gate Repair.
Pricing reflects the Pembroke Pines market as of 2026. Tidewater Gate Repair offers free estimates – call (877) 748-7198.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Keisha Ingram"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Diego Morales"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Ebony Dawson