Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Pembroke Pines?
Gate parts and welding in Pembroke Pines typically run from about $150 to $1,800, with most single-part repairs and small weld jobs landing between $250 and $650. Small hardware like a hinge, latch, roller, or stop bracket usually costs $150 to $350 installed, while bent-panel welding and track repairs climb from $300 to $900. Full gate frame fabrication, post welding, or rebuilding a damaged leaf is a bigger job, estimated at $900 to $1,800 and up depending on the material and the condition of the gate.
We work on gates, only gates, so the technician who shows up already knows the hardware in front of them. That matters more than you’d think when a gate is hanging off a sagging post or a weld has cracked for the second time. Call (877) 748-7198 and we’ll set up a free estimate for your gate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what the piece of repair closest to your gate usually costs in Pembroke Pines. These are typical ranges for parts plus the labor to install or weld them, and the written estimate you get on-site sets the final price.
| Gate part or welding job | Typical 2026 range |
|---|---|
| Single hinge, latch, or stop bracket | $150 – $350 |
| Roller, guide wheel, or track hardware | $180 – $400 |
| Weld repair on a cracked hinge plate or post mount | $250 – $550 |
| Straightening and re-welding a bent gate leaf | $300 – $700 |
| Weld repair on a slide gate track or guide rail | $350 – $800 |
| Gate post reinforcement and re-welding | $400 – $900 |
| Hanging and aligning a replacement gate leaf | $500 – $1,100 |
| Custom frame fabrication and re-weld (small residential gate) | $900 – $1,800 |
| Worn hardware replacement alongside an opener repair | Adds $120 – $350 to the estimate |
What pushes a price up is usually not the part itself. It’s the condition of the post the gate hangs on, whether the gate is aluminum, steel, or wrought iron, and how much of the weld has to be ground down before the new weld can hold. Aluminum gate frames need different welding equipment and technique than steel, and older wrought iron can be porous after cycles of heat and humidity, so a technician spends more time preparing the surface than a quick weld job would suggest. A sagging post is a common one in South Florida, where the ground can shift with heavy rain and a post set years ago has moved just enough to throw the gate off. On the other end, swapping a latch or a hinge on a gate that’s already square and true is fast work and lands at the low end of the range.
If your gate is fine mechanically but won’t open, you’re likely looking at a different repair. Our electric gate repair in Pembroke Pines page covers motors, control boards, and wiring. And if you need the whole system assessed before committing, the gate repair service in Pembroke Pines page explains how a diagnostic call works.
What Affects Gate Parts & Welding Pricing in Pembroke Pines
- Gate material. Aluminum, steel, wrought iron, and ornamental frames all weld and hang differently, and the tools and prep change with the metal. Aluminum welding and wrought iron work both take longer than a plain steel weld, which moves the estimate up.
- Gate weight and leaf size. A heavier leaf needs more support at the hinge and post, so reinforcing the frame is often part of the job. A single-entry residential gate is a lighter lift than a wide double-leaf drive gate, which runs taller on hardware and weld time.
- Condition of the post. A post that has shifted or rusted through at the base will need reinforcement or replacement before any hinge or weld holds. Pembroke Pines has plenty of gates on older posts, and if the footing is fine, we can often re-weld the mount instead of rebuilding.
- Whether the gate is manual or automated. Hardware on an automated gate has to be aligned tightly enough that the opener doesn’t fight the gate. If we’re welding a hinge on a gate run by a LiftMaster or FAAC operator, we check the swing or slide clearance to make sure nothing drags.
- Metal prep and paint. Grinding down old weld, cleaning rust, and re-priming the repaired spot is real work, and skipping it shortens the life of the repair. We’ll show you what’s involved before we start.
- Access and property type. Residential gates are usually straightforward. HOA and commercial gate welding may involve coordinating access with the property manager, and that coordination is factored into the estimate.
If you’re weighing a repair against a fresh system, read our guide on repair or replace before you decide. Replacement rarely pays off when the frame is sound and only the hardware has failed.
How to Save on Gate Parts & Welding
The cheapest repair is the one done right the first time. A hinge or weld that fails twice costs more than a careful fix. Here’s what actually keeps the bill down:
- Catch small hardware problems early. A latch that sticks, a hinge pin that wobbles, or a roller that grinds are all $150 – $350 fixes on their own. Left alone, they wear the gate frame and turn into a $500 – $900 weld job.
- Have the post checked while we’re on-site. If we’re already welding a hinge, we can check the post and footing in the same visit. A stable post means the repair lasts; a soft one means we’ll flag it before it fails.
- Bundle gate hardware with an opener repair. If your electric gate opener repair in Pembroke Pines call reveals worn rollers or a fatigued hinge, doing both in one visit saves a second trip.
- Ask for the written estimate before work starts. Our estimates are free and itemized, so you can see parts and labor separately and decide what fits your budget.
- Keep the metal protected. Touching up paint on a welded spot keeps rust from creeping into the frame. In Pembroke Pines humidity, a bare weld will start to oxidize within a season.
For a quick look at pricing on a specific repair, our gate repair costs in Pembroke Pines guide walks through typical ranges by job type. And if you’re already thinking of upgrading rather than repairing, the gate installation in Pembroke Pines page covers what a new system involves. When you’re ready to price your repair, call (877) 748-7198 for a free estimate.
What Happens When You Call
We answer 24/7. When you call, we take down the gate type, the brand if you know it, and what it’s doing or not doing, then book a time for a technician to come out. Fast dispatch, 7am – 7pm, Sunday through Friday. The technician inspects the gate, the post, and the hardware, then walks you through what’s wrong and what the estimate covers. You get the written estimate before we pick up a tool. If the welding can’t be done safely on-site, we’ll tell you and give you the next option.
We service gates only, which means every call on our schedule is a gate call. Whether your property runs a Mighty Mule on a home driveway or a DoorKing on a managed entrance, the technician arrives knowing the hardware and how it normally behaves.
A Safety Note on Gate Welding and Structure
Welding on a gate frame and adjusting the hardware that carries the leaf’s weight are jobs worth handing to a trained technician. A gate that lets go of a hinge, or a slide gate that jumps the track, carries enough mass to seriously injure someone. The dangerous parts on a gate are the operator’s power and wiring, the heavy panels themselves, and a slide gate off its track. Before you try to adjust or re-weld a mount yourself, get a trained pro to look at it. We’ll flag any structural concern during the estimate.
FAQs – Gate Parts & Welding Cost
How much does a gate weld repair cost in Pembroke Pines?
Most gate weld repairs in Pembroke Pines cost between $250 and $800, depending on whether the weld is on a hinge plate, a track, or a gate post. Preparation and re-painting are usually a meaningful part of the bill. Call (877) 748-7198 for a free estimate, and we’ll tell you what your weld job actually needs.
Is it cheaper to repair gate hardware or replace the whole gate?
For almost all hinge, latch, and weld failures, repair costs far less than replacement. A $150 – $350 hardware swap is a fraction of a custom gate frame fabrication, which typically runs $900 – $1,800 and up. Replacement makes sense when the frame has rusted through or the post is beyond reinforcement. Our guide on whether to repair or replace your gate helps you sort that out, and a free estimate settles it with numbers.
Can you replace a single gate hinge in Pembroke Pines?
Yes. A single hinge replacement in Pembroke Pines typically runs $150 – $350, and we can usually match the existing hardware to keep the gate looking the way it did. If you have a matching hinge or want us to source one, just mention it when you call (877) 748-7198. Our gate hinge repair in Pembroke Pines service covers the finer details.
How much does gate hardware cost alongside an opener repair?
Worn rollers, hinges, or latches found during an opener repair usually add $120 – $350 to the estimate. Doing both in one visit is more efficient than a second trip. If your gate isn’t opening at all, it may be a motor, control board, or wiring issue, and that’s handled on our electric gate repair in Pembroke Pines page. Call (877) 748-7198 for a free estimate.
Do you work on both manual and automated gate welding?
Yes. We handle manual gates and automated systems under one roof, from residential platforms like Viking and Ghost Controls to commercial-grade systems like BFT and Elite. That way you’re not sourcing a separate welder for the gate and a separate op
What Our Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Ebony Dawson"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Rafael Reyes"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Keisha Ellison